Please comment on your experience so I can make an educated decision on which mount to get. I've read and seen the vids on ASR mounts and already own AAC with 51T and have my busted-up MAAD mount. However, I own an AAC suppressor also and have a 51T on another rifle, but this doesn't trump my lust for how simple the ASR mount and muzzle devices seem to be (never handled any ASR stuff). The ASR seems like a simple, effective, and positive-locking design and ASR muzzle devices seem to be less bulky than the Saker and the 51T muzzle devices (smaller diameter at the barrel-threads). Still not sure what caused it, but Silencerco has been amazing with support and I can choose which mount and muzzle devices I want for a replacement. It left a couple small gouges in my MAAD muzzle break also. The MAAD mount seemed stripped and just spins around with obvious play inside, where it normally makes those warm and fuzzy clicking noises. I was shooting outdoor range, so no road-rash from concrete either. After retrieving it, thankfully NO END-CAP STRIKES. You can lock your 419 mount on the gun, mount in the can, grease your LH thread and. My Saker556 was ordered with a MAAD mount which has been fine for a few hundred rounds, but recently it was launched down range. The nice thing about LH thread is they wont come loose, theyll tighten on. First decide what your priorities of use are and choose the best suppressors to fit that role, then decide what mount you prefer and last pick a compatible MD you are kind of working backwards by trying to go from MD to suppressor.For shooters who've handled a Silencerco suppressor, more specifically a Saker556, which mount have you had the most confidence in? By confidence, I'm talking about ease of attachment and positive clicks as it secures to the muzzle device, a secure feeling as it locks down, and generally gives you a warm fuzzy feeling that its secured and also that its gonna be easily removed at a later date. I would echo what others are saying regarding choosing a suppressors. You didn't mention what you're mounting or mounting to, but check out Dead Air's Xeno mounts. I do like Dead Air's taper/gas seal on their muzzle devices, but keymo does add a good bit of length and weight. Press question mark to learn the rest of the keyboard shortcuts. I have never used it and took it off when I first purchased my Chimera. The Bowers Group 3-lug insert is designed to work with any Bowers subgun/carbine silencer with an AIMS mount. I have no direct experience with silencerco's asr but work with a guy who has them and to my knowledge he hasn't had any troubles. I have an unused SiCo ASR Charlie Mount that came with my Chimera. AIMS Mount Accessories Versadapt 3-lug Insert. (I know because I spoke with them regarding sandman vs nomad). Works with any suppressor with 1.375×24 x 24 rear cap threads. That being said the nomad has no barrel restrictions, is rated to 300 Norma mag and has a lifetime warranty (note that the sandman series is only rated to 300wm, this is due to the keymo Mount not being tested and proven on calibers greater than 300wm - dead air)Īs others have said, if you still have questions about the durability of the nomad just look at what mageever has said or reach out to dead air they will gladly make recommendations for your use scenario. You trade some durability with the nomad for decreased weight and adaptability (I.e industry standard rear thread mounts). Weight, size (length), price and engineering seemed the best with Q. ASR would have been a cheap swap, but I cant lock it under the handguard. If you’re the guy that will you probably already know that and know what you need to buy. I researched a bunch of alternatives (Area 419, Deadair Keymo, Griffin, and SiCos ASR) for my Saker 762 MAAD mount change and I just settled on Q Plan-B and Cherry Bombs. But as far as construction, I believe most people will never experience the difference. Made from aerospace grade 17-4PH Stainless Steel, Titanium mounts are made from US made 6AL4V. To remove the suppressor, turn the lock ring to unlock the cam against. Suppressor mount allows you to use your compatible suppressors with the Hellfire Self Timing Brake system by simply removing your Hellfire Brake and installing one of these mounts. The cam locks against spring tension, so the suppressor locks in place and cannot vibrate loose. I can’t directly compare sound as I have a Sandman-k and a nomad. Thread the suppressor’s ASR mount onto the ASR muzzle device and lock the suppressor in place with the lock ring of the spring-loaded cam mechanism on the suppressor mount.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |